ChicagoDiscus.com     Cafepress Store

Results 1 to 8 of 8

Thread: Heater to go with my Ranco controller

  1. #1
    Registered Member
    Join Date
    Mar 2015
    Posts
    98
    Real Name
    Tim

    Default Heater to go with my Ranco controller

    Currently have two Jager 200w heaters on my controller for a 75g tank.

    Just purchased a 180 and sump will hold approximately 15 gallons of water. So I'm figuring right under 200 gallons.
    My ambient during the winter is around 68 and summer is around 75.

    The Jagers are really long so I'm thinking of going with a couple of Titaniums from Jehmco. What wattage would you
    recommend to keep my tank at around 85-83 ?

    My sump is going to be two small to accommodate the Jagers and the titaniums seem to run smaller, once I figure out wattage
    I will Jehmco for measurements.


    Thanks

  2. #2
    Registered Member
    Join Date
    Mar 2008
    Location
    B'ham, Alabama
    Posts
    478

    Default Re: Heater to go with my Ranco controller

    Tim,

    I found this on the web which mostly agrees with what I have been taught.

    Tank Size Heat 5ºC/9ºF Heat 10ºC/18ºF Heat 15ºC/27ºF
    5 gal/25 L 25 watt 50 watt 75 watt
    10 gal/50 L 50 watt 75 watt 75 watt
    20 gal/75 L 50 watt 75 watt 150 watt
    25 gal/100 L 75 watt 100 watt 200 watt
    40 gal/150 L 100 watt 150 watt 300 watt
    50 gal/200 L 150 watt 200 watt two 200 watt
    65 gal/250 L 200 watt 250 watt two 250 watt
    75 gal/300 L 250 watt 300 watt two 300 watt

    Which would suggest approximately 800 watts should be plenty.

    I believe 15 gallons for your sump is way too small, I would suggest at least a 40 gallon breeder tank should be the minimum; I know you did not ask about the sump size, but I did not charge for my opinion, ha.

    Ron

  3. #3
    Registered Member
    Join Date
    Mar 2015
    Posts
    98
    Real Name
    Tim

    Default Re: Heater to go with my Ranco controller

    Quote Originally Posted by alron2 View Post
    Tim,

    I found this on the web which mostly agrees with what I have been taught.

    Tank Size Heat 5ºC/9ºF Heat 10ºC/18ºF Heat 15ºC/27ºF
    5 gal/25 L 25 watt 50 watt 75 watt
    10 gal/50 L 50 watt 75 watt 75 watt
    20 gal/75 L 50 watt 75 watt 150 watt
    25 gal/100 L 75 watt 100 watt 200 watt
    40 gal/150 L 100 watt 150 watt 300 watt
    50 gal/200 L 150 watt 200 watt two 200 watt
    65 gal/250 L 200 watt 250 watt two 250 watt
    75 gal/300 L 250 watt 300 watt two 300 watt

    Which would suggest approximately 800 watts should be plenty.

    I believe 15 gallons for your sump is way too small, I would suggest at least a 40 gallon breeder tank should be the minimum; I know you did not ask about the sump size, but I did not charge for my opinion, ha.

    Ron
    Thanks, the sump is approximately 35 gallons, I was guesstimating how my water will be in it.

  4. #4
    Homesteader Adam S's Avatar
    Join Date
    Jul 2017
    Posts
    741

    Default Re: Heater to go with my Ranco controller

    ((85°F-68°F)/10)*(3w to 5w)*200 gallon = 1000w-1700w. This doesn't take into account any insulative properties your setup may have, but 1000w should be your minimum. 2-3 smaller heaters are still better than 1 even with a controller.

  5. #5
    Registered Member
    Join Date
    Mar 2015
    Posts
    98
    Real Name
    Tim

    Default Re: Heater to go with my Ranco controller

    Thanks, I will probably go for 3 400w heaters from Jehmco then.

  6. #6
    Registered Member
    Join Date
    Mar 2015
    Posts
    98
    Real Name
    Tim

    Default Re: Heater to go with my Ranco controller

    I am going with a couple 500 watt heaters and will add a third if needed. Should I go with Finnex or Jehmco. If Jehmcho, are the bulkhead recommended ? Last thibg, can the Ranco handle 1500 watts if I find the need for it ?

  7. #7
    Registered Member
    Join Date
    Mar 2008
    Location
    B'ham, Alabama
    Posts
    478

    Default Re: Heater to go with my Ranco controller

    Tim,

    Most of the controllers I found were rated at 1000 watts or less. I would be worried that my controller would fail in the on position and fry my tank. I would buy a separate controller "10A 110V Digital LED Fahrenheit Temperature Controller Thermostat Temp Sensor" for each heater. I found them for less than $11 each (buy a couple extras for repairs). You will have to add a power cord and plug but that should be less than $10.

    https://www.ebay.com/itm/10A-110V-Di....c100005.m1851

    What do you think?

    Ron

  8. #8
    Homesteader Adam S's Avatar
    Join Date
    Jul 2017
    Posts
    741

    Default Re: Heater to go with my Ranco controller

    Ranco ETC 111000 handles up to 1500w, 1800w for the heavy duty version. These are as good as they come.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Cafepress