RO Problems

[Trier20]

I recently bought a used RO unit from the LFS. Owner only had it working for 3 months then figured out he needed a larger one. This is a 300gpd unit. It had a section of tubing missing where I later found out this is were a permeate pump was. It has to membranes on it and 3 canisters at 20-40 miscrons, 10 microns and 5 microns. When I first got this unit the pressure ran about 55psi. I switched out the canister filters to the ones mentioned now and shortly after that my pressure has dropped to about 20-23psi. I'm looking to purchase a booster pump for the unit but before I do that do you think i should get new membranes for it? Oh also the production went from about 200gpd to around 60-80. Thanks

[Keith Perkins]

I don't have an answer to your question Brandon, but I do have a question. Do you know how long the unit sat idle before you got it and what was done with the membrane during that time? I question the condition of the membrane based on the fact your water production went down when you changed your filters. My unit isn't that old and I've only changed out my filters once so far, but production and pressure sure didn't drop off when I did it.

[nwehrman]

Does it have a flush on it? The flow restrictor also could be clogged.


Nicole

Sent from my iPhone using Tapatalk

[Trier20]

Nicole ill be honest. I wouldn't know what a flush looks like if it jumped out and but me. I'll take a pic and post it see if you can recognize anything.

[Keith Perkins]

I'd do a little goggling with Nicole's suggestions.

[Trier20]

I don't have an answer to your question Brandon, but I do have a question. Do you know how long the unit sat idle before you got it and what was done with the membrane during that time? I question the condition of the membrane based on the fact your water production went down when you changed your filters. My unit isn't that old and I've only changed out my filters once so far, but production and pressure sure didn't drop off when I did it.

Keith I'm not sure how long it sat idle.

[Trier20]

ImageUploadedByTapatalk1351567600.096804.jpg

[Trier20]

ImageUploadedByTapatalk1351567619.747174.jpg

[Tommo]

Here's a pic showing the flush on a RO unit. It's best to flush the membrane once a week to extend the its life.

2-stage-with-twin-o-rings-400-228x228.jpg

Hope this helps?

[Trier20]

So you close that and let the water drain out? Mine doesn't have that.

[Brent1972]

So you close that and let the water drain out? Mine doesn't have that.

Have a look at this vid http://www.youtube.com/watch?v=mW7rYNyL2eY It should explain all .

In the second pic you have a auto shut off valve fitted.

[Trier20]

Thanks Brent! Yea I have one of the flush kits but I don't have the restrictor on it....... this is where the section of hose is missing. So the water has been flowing unrestricted through the unit. Looks like I may have to go over and through the entire thing.....*sigh*

[Mr.Al]

Hi Trier20, if you have a store hereby you that produces and sells bottled R/O water and services R/O units they sell, they might be able to look at your unit and see what is wrong and what parts you need to run your unit properly. I use to have a 150gdd unit with booster pump and even though I didn't purchased the unit from them. They were very kind to flush the member and replace the inserts for the housing units. I know my unit came with a back flush, and I used everytime before having the unit produce R/O water. The waste water outpour is higher than the R/o output. The pressure gauge read around 35 to 50ppm and it did take 24 hours to get the 150gpd. Keeps us posted on how things work out for ya....Mr.Al

[DiscusLoverJeff]

Brandon,

There are 2 types of flow restrictors, one that looks like this, it seats inside the end of the tubing

http://www.marinedepot.com/ps_viewit...FegWMgodZkcAbg

And then there is this type. Which if you had it, you would spot it.

http://www.waterfiltersfast.com/FLOW..._source=nextag

Since we both have a 300gpd unit, I can tell you that you will find out quickly that you will burn through filters faster depending on your daily usage.

I had to install a pre filter, followed by the booster pump, then the ro unit, then to the DI unit.

Hopefully all you need is to install the flow restrictor, which in your case would be at least a 1200. Once you do that and if you find your pressure is still low, you may need to do what I did and replace all the filters and membrane. Now my system is holding at 80psi.

Good luck!

[nwehrman]

I have the second type of flow restrictor Brandon. But either would work, just be sure it's sized for your membrane.




Nicole

Sent from my iPhone using Tapatalk