python problems

[bottle-blonde]

i just went out and bought a python only to discover that my sink faucet has no threads for me to screw the thing on with. so much for making things faster. i guess i'll go back to the pet store and return it now... grrrr.

[georgef]

Hey, bb --

The good doctors Foster and Smith have a universal adapter you can get here:

http://www.drsfostersmith.com/produc...mp;pCatId=3922

[mench]

depending on what type of faucet you have,it either should unscrew or it should have threads on it,either way you can get adapters for it so ya can use the Python.

Mench

[bottle-blonde]

i wonder if they have something like that at local hardware stores. i want to play with my new toy now and don't want to have to wait for mail order.

your post gave me hope though so maybe i won't return the python.

thanks!

[Carol_Roberts]

The python may have come with an adapter. By the way, I don't use the part where you hook it to the faucet to drain your tank. I just thow the other end out the door or in the bathtub to drain and clean the tanks. To refill my water storage tanks, I attach the python to my faucet just like you attach a garden hose to a faucet. I don't use that funny shaped green piece at all.
Carol

[georgef]

I don't believe it comes with the universal adapter. At least mine didn't.

I'm sure you could take that "funny shaped green piece" to the hardware store and tell them what you need and they can fix you right up. The "universal adapter" is nothing more than a stainless steel or brass fitting that screws into the faucet pump and is attached via a rubber hose to your faucet with a hose clamp. The pieces parts would probably cost less at the hardware store than the "universal adapter", too.

[RAWesolowski]

BB!

Don't return the Python, replace your faucet!

I agree with Bob.. lol.... Phython 2 Faucet 0......

Julz

I had this problem when I started using my python to drain and fill the tank in my bedroom.

the bathroom sink faucet had no threads, I tried that universal adapter, found it at Canadian Tire, it was garbage the water pressure kept blowing it off no matter how tight I screwed it on.

eventually what worked is, I got a brass python adapter and took apart the faucet, I removed the aerater and flow reducer stuff, and inside behind all that junk was threads that the adapter could screw into.

So get a wrench out and have a look.

hth

[Carol_Roberts]

Yes, I have threads inside the bathroom facucet, and outside of the kitchen faucet.
Carol

[daninthesand]

Try a place that carries waterbeds. They usually have adapters for filling from the tap. They also sell, devices basically identical to python except without the hose

Daniel

[bottle-blonde]

i have no threads anywhere and as a renter that doesn't want to stay here very long i'm not going to mess around with that stuff. besides, lifting buckets really is quite a good upper body workout!

[Rick_May]

BB,
I really think your missing the part about unscrewing the aereater its the last part on your faucet.

[Rick00]

BB,

wait till u see your water bill....those things waste a ton of water....i bought a small utility pump and connected to my python. I pump the water and crap out and then hook it up to the facet.........the pump will pay for itself in a month....

Rick

[Richman]

Your local hardware store has a connection called a "dishwasher hose adapter". They are made to allow you to use a diswasher that has hoses and attaches to the kitchen sink directly. One end will screw onto your faucet when you remove the aereator. I'm sure you have one. The other end is threaded for a water hose. Your water will flow out a lot stronger than normal. I have one on my bathroom faucet. When cleaning the tank, I just start a siphon by pinching the hose about 3 feet below the python--then fill the 3 feet of hose and the large end completely with water--drop the whole end into the tank--and the siphon starts. I just put the other end under the toilet lid and the water empties there. When the cleaning process is done, just attach the other end to the faucet and fill the tank. The advantage is that you can adjust the hot and cold so that the water goes into the tank at just the right temp. After the tank is filled, I add Amquel. My KH is 3 and my GH is 7. Ph 6.8 ---right from the tap. I'm in heaven. Trying to use a python with the waterbed type connection that siphons with water pressure exerted by running water will run your water bill sky high. You don't need that at all. Just get the siphon started and it will give you plenty suction to deep clean gravel(if you have it). The end where the water runs out just needs to be quite a bit lower than the tank.